solid flow

Mathematic Model of Liquid Solid Flow in Gap Flow Field of EDM

镜面电火花加工间隙流场中流体运动的数学建模

Based on the laws, one model of solid flow-rate was founded by developing relation of thermal balance around probe and tested.

在此基础上，利用探头温度径向影响区域规律和热平衡关系建立了固体流量测量模型。

A study of the minimum tailwater depth required to form the bucket flow in solid bucket type energy dissipators some approaches to form interacting functions in Fredholm integral equations method of elastic mechanics

实体消力戽起戽水深的研究弹性力学的Fredholm积分方程组解法中构造影响函数的几种方法

The structure and operating principles of a self pumping continuous flow liquid/ solid centrifugal separator based on the principle of self pumping continuous flow centrifugation intro-duced by this auther are reported here.

本文报导了根据作者最近提出的自抽连续离心原理而研制的自抽连续液/固离心分离机的结构和工作原理。

Objective To study the effect anisotropic hydraulic conductivity coefficient on interstitial fluid flow in solid tumor.

目的研究实体肿瘤组织间质各向异性传导系数对流体流动的影响.

The formula for calculating the solid flow rate in gas-solid flow oy using venturi meter is presented, which is also linear under certain conditions.

最后得出气&固两相流中，用文丘利流量计测量固相流率时的计算公式。它在一定条件下也是线性的。

Numerical Simulation of Three-dimensional Isothermal RTM Process Based on Solid Flow

基于实体流的三维等温RTM数值模拟

Abstract Based on the theory of flow of solid-fluid mixtures and dimension analysis, the study result of the pressure losses along the height above a circulating fluidized bed is presented.

本文从气固流动理论及因次分析两方面研究了循环流化床中主床沿床高方向的压力损失。

The flow of compressible fluid in porous medium is a result of coupling of liquid flow and solid deformation. It is rather important to study the law of fluid solid interaction.

可压缩流体在多孔介质中的流动过程是流体流动和固体变形相互耦合作用的结果，研究多孔介质中流固耦合渗流规律对于完善流固耦合理论以及工程应用有着重要意义。

The Effect of a Central Flared Angle on the Gas solid Flow Characteristics at the Outlet of a Radial Bias and Pulverized coal Swirl Burner

中心扩口对径向浓淡旋流煤粉燃烧器出口气固流动特性的影响

The solid heat conduction along the flow direction and the regenerator heat storage capacity for the unit volume has no impact on temperature efficiency peak and optimal switch time.

沿气流流动方向固体导热和单位质量固体蓄热能力不影响温度效率峰值和最佳切换周期。

The methods and devices to control the circulation solid flow pneumatically are studied in this paper.

因此,本文主要研究通过气动方式控制循环流化床循环物料的方法和装置.

Much research work on the visualization of gas solid flow in circulating fluidized bed has been carried out in Shanghai Jiaotong University.

上海交通大学在流化床燃烧气固两相流可视化研究方面做了大量细致的工作，取得初步成果，文中对此做了评述。

Material flow considerations are vitally important for both foam and solid mouldings.

考虑材料流动对发泡成型和固体成型,都非常重要.